flexural modulus matweb

Titanium Ti-6Al-4V (Grade 5), Annealed - asm.matweb.com..Alpha-Beta Alloy. Applications: Blades, discs, rings, airframes, fasteners, components. Vessels, cases, hubs, forgings. Biomedical implants. Biocompatibility: Excellent, especially when direct contact with tissue or bone is required. Ti-6Al-4V's poor shear strength makes it undesirable for bone screws or plates. It also has poor...

Aluminum 2024-T4 - asm.matweb.com..A high strength material of adequate workability. Has largely superceded 2017 for structural applications. Uses: Aircraft fittings, gears and shafts, bolts, clock parts, computer parts, couplings, fuse parts, hydraulic valve bodies, missile parts, munitions, nuts, pistons, rectifier parts, worm gears, fastening devices, veterinary and...

Overview of materials for High Density Polyethylene ... - MatWeb.... Modulus of Elasticity, Average value: 0.883 GPa Grade Count:9; Flexural Yield Strength, Average value: 62.5 MPa Grade Count:5; Flexural Modulus, Average value: 1.19 GPa Grade Count:68; Secant Modulus, Average value: 0.869 GPa Grade Count:6; Izod Impact, Notched, Average value: 2.17 J/cm Grade Count:29...

Overview of materials for PVC, Extruded - MatWeb.... Tensile Strength, Yield, Average value: 34.0 MPa Grade Count:179; Elongation at Break, Average value: 272 % Grade Count:392; Elongation at Yield, Average value: 5.33 % Grade Count:3; Modulus of Elasticity, Average value: 2.84 GPa Grade Count:75; Flexural Yield Strength, Average value: 81.4 MPa Grade Count:66...

Flexural Strength Testing of Plastics - MatWeb.This page describes the ASTM D790 flexural property test for plastics and gives average values of flexural strength and flexural modulus for common polymers such as nylon, polyethylene, polypropylene, and acrylic.

Tensile Property Testing of Plastics - MatWeb.Tensile property tests for plastics are illustrated and give average values of ultimate tensile strength, elongation, and tensile modulus for common polymers such as nylon, polyethylene, polypropylene, and acrylic are reported.

Aluminum 6061-T6 - asm.matweb.com..Combines relatively high strength, good workability, and high resistance to corrosion; widely available. The T8 and T9 tempers offer better chipping characteristics over the T6 temper. Applications: Aircraft fittings, camera lens mounts, couplings, marines fittings and hardware, electrical fittings and connectors, decorative or...

Ensinger Tecamid? 6/6 Nylon (PA66) - MatWeb.Available Properties. Density, ASTM D792; Water Absorption, ASTM D570, at 24 hours; Water Absorption at Saturation, ASTM D570; Hardness, Rockwell M, ASTM D785; Tensile Strength, Yield, ASTM D638; Elongation at Break, ASTM D638; Tensile Modulus, ASTM D638; Flexural Strength, ASTM D790; Flexural Modulus,...

Overview of materials for Gray Cast Iron - MatWeb.Tensile Strength, Yield, 65.5 - 172 MPa, 9500 - 25000 psi, Average value: 124 MPa Grade Count:6. Elongation at Break, 1.00 - 15.0 %, 1.00 - 15.0 %, Average value: 6.67 % Grade Count:6. Modulus of Elasticity, 62.1 - 162 GPa, 9000 - 23500 ksi, Average value: 118 GPa Grade Count:15. Flexural Yield Strength, 421 - 641...

BASF Ultramid? 8202 PA6 (Dry) - MatWeb.It combines good strength, stiffness and toughness as well as excellent heat, chemical and abrasion resistance. ... Elongation at Yield, ASTM Test; Tensile Modulus, ISO 527, 1mm/min; Tensile Modulus, ISO Data; Tensile Modulus, ISO Data; Flexural Strength, ISO Data; Flexural Strength, ASTM Test; Flexural Strength, ASTM...